Welcome to the website of Dalian Barnet Flex Hydraulic Co., Ltd.!

搜索
Search
BNTFLEX @ WhatsApp

BNTFLEX Hotline
You can contact the BNTFLEX SERVICE Hotline at the phone number +8618322701295
Open Number directly in click here.

BNTFLEX SALES Hotline
You can contact the BNTFLEX SALES Hotline at the phone number+8618522290645
Open Number directly in WhatsApp click here.
imgboxbg

NEWS CENTER

Position:
Homepage
/
/
/
How to operate the hose crimping machine

How to operate the hose crimping machine

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-11-07
  • Views:0

(Summary description)working principle:
 The oil pump of the hose crimping machine outputs the hydraulic oil under the power of the motor, and pushes the piston in the hydraulic cylinder to reciprocate, so that the pressure block pushes the mold base, so that the mold base can perform radial contraction movement, and finally realize the module to withhold the hose . When the shrinkage reaches the value set on the control panel, the crimping is automatically stopped, the reversing valve is automatically reversed, and the hydraulic oil enters the lower cavity of the cylinder to drive the upper plate to move upwards. The mold hole is enlarged. Remove the crimped hose That's it.
Introduction to the use of the crimping machine:
1. The crimping machine should be crimped 25 times without load during the first use, and observe whether each part can be used normally.
2. When the crimping machine is used in winter, it should be withheld 25 times without load to increase the oil temperature.
3. Next, press the button to open. After the mold base is opened, select the corresponding mold and install it on the mold base according to the specifications of the clamped hose, and adjust the micrometer scale.
4. Place the hose with the joint in the proper position in the crimper head, and crimp the entire length at one time.
5. Press the crimping button for crimping operation until the crimping head stops crimping.
6. After **, take out the crimped hose and use a vernier caliper to check the size of the crimped joint jacket. The parameter table does not meet the scale of the micrometer to be adjusted until the next hose meets the requirements.
Precautions for pipe press:
1. When crimping, put the joint in the center of the mold, not on the hexagonal nut.
2. Prevent tools and sundries from entering the crimper head.
3. After the work is completed, the eight mold bases are opened to a large extent, so that the spring can be in an open state and the oil cylinder is also in a pressure relief state to extend the life of the oil seal.

How to operate the hose crimping machine

(Summary description)working principle:
 The oil pump of the hose crimping machine outputs the hydraulic oil under the power of the motor, and pushes the piston in the hydraulic cylinder to reciprocate, so that the pressure block pushes the mold base, so that the mold base can perform radial contraction movement, and finally realize the module to withhold the hose . When the shrinkage reaches the value set on the control panel, the crimping is automatically stopped, the reversing valve is automatically reversed, and the hydraulic oil enters the lower cavity of the cylinder to drive the upper plate to move upwards. The mold hole is enlarged. Remove the crimped hose That's it.
Introduction to the use of the crimping machine:
1. The crimping machine should be crimped 25 times without load during the first use, and observe whether each part can be used normally.
2. When the crimping machine is used in winter, it should be withheld 25 times without load to increase the oil temperature.
3. Next, press the button to open. After the mold base is opened, select the corresponding mold and install it on the mold base according to the specifications of the clamped hose, and adjust the micrometer scale.
4. Place the hose with the joint in the proper position in the crimper head, and crimp the entire length at one time.
5. Press the crimping button for crimping operation until the crimping head stops crimping.
6. After **, take out the crimped hose and use a vernier caliper to check the size of the crimped joint jacket. The parameter table does not meet the scale of the micrometer to be adjusted until the next hose meets the requirements.
Precautions for pipe press:
1. When crimping, put the joint in the center of the mold, not on the hexagonal nut.
2. Prevent tools and sundries from entering the crimper head.
3. After the work is completed, the eight mold bases are opened to a large extent, so that the spring can be in an open state and the oil cylinder is also in a pressure relief state to extend the life of the oil seal.

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-11-07
  • Views:0
Information

working principle:
 The oil pump of the hose crimping machine outputs the hydraulic oil under the power of the motor, and pushes the piston in the hydraulic cylinder to reciprocate, so that the pressure block pushes the mold base, so that the mold base can perform radial contraction movement, and finally realize the module to withhold the hose . When the shrinkage reaches the value set on the control panel, the crimping is automatically stopped, the reversing valve is automatically reversed, and the hydraulic oil enters the lower cavity of the cylinder to drive the upper plate to move upwards. The mold hole is enlarged. Remove the crimped hose That's it.
Introduction to the use of the crimping machine:
1. The crimping machine should be crimped 25 times without load during the first use, and observe whether each part can be used normally.
2. When the crimping machine is used in winter, it should be withheld 25 times without load to increase the oil temperature.
3. Next, press the button to open. After the mold base is opened, select the corresponding mold and install it on the mold base according to the specifications of the clamped hose, and adjust the micrometer scale.
4. Place the hose with the joint in the proper position in the crimper head, and crimp the entire length at one time.
5. Press the crimping button for crimping operation until the crimping head stops crimping.
6. After **, take out the crimped hose and use a vernier caliper to check the size of the crimped joint jacket. The parameter table does not meet the scale of the micrometer to be adjusted until the next hose meets the requirements.
Precautions for pipe press:
1. When crimping, put the joint in the center of the mold, not on the hexagonal nut.
2. Prevent tools and sundries from entering the crimper head.
3. After the work is completed, the eight mold bases are opened to a large extent, so that the spring can be in an open state and the oil cylinder is also in a pressure relief state to extend the life of the oil seal.

Keyword:

Scan the QR code to read on your phone

CONTACT FORM

We’ll take the time to explain the recommended solution and its price

Username used for comment:
Customer message
Description:

BNTFLEX SOCIAL

pinterest
pinterest
twitter
twitter
facebook
Bntflex
youtube
youtube

CONTACT

Copyright © 2019 Dalian Barnett Flex Hydraulics Co.,Ltd.       辽ICP备20000203号

电话

邮箱

产品