Introduction To The Power Source Of The Crimping Machine
Time of issue:
2022-01-24
Introduction To The Power Source Of The Crimping Machine How accurate and harmonious is the force and position of the hydraulic cylinder of the hose crimping machine? The hydraulic cylinder of the hose crimping machine can be under the force closed-loop control or the position closed-loop control method, respectively, and in the position mode, then the force value is a detected value and is not controlled on site. In force mode, position is only controlled as undetected field. What everyone is generally concerned about is that the switching between force control and position control should be smooth. This conversion process has rich instructions in the DELTA controller that can be automatically completed. Check whether the protective devices on the hose crimping machine are complete. If they are not installed, it is forbidden to drive the intermediate frequency tube pressing machine. There should be good grounding and electrical disconnection, and the voltage should be stable. Check the lubricating parts of the hose crimping machine, and add enough oil when there is no oil or no oil. When withholding hoses of different specifications, the indenters of different specifications should be replaced. When oil leakage is found after long-term use, the seals in the oil cylinder and pipe valve system should be replaced in time. The hydraulic oil is 46# Great Wall brand anti-wear hydraulic oil, and the oil temperature is usually controlled at 30℃~35℃. In the course of use, dust and other debris will inevitably enter, and the mold directly contacts the withheld pipe fittings, so the cleanliness of the connecting mold is also one of the conditions for extending the service life of the crimping machine and the mold. The strong magnetic mold is adsorbed on the mold seat by super-strong magnetic force. The contact surface between the mold and the mold seat should be kept clean. Always wipe the bottom of the mold and the contact surface of the mold seat with clean cotton yarn. After wiping clean, oil the mold immediately to prevent dust particles. The entry of impurities and other impurities will cause the wear of the mold and the mold seat.
Introduction To The Power Source Of The Crimping Machine
How accurate and harmonious is the force and position of the hydraulic cylinder of the hose crimping machine? The hydraulic cylinder of the hose crimping machine can be under the force closed-loop control or the position closed-loop control method, respectively, and in the position mode, then the force value is a detected value and is not controlled on site. In force mode, position is only controlled as undetected field. What everyone is generally concerned about is that the switching between force control and position control should be smooth. This conversion process has rich instructions in the DELTA controller that can be automatically completed.
Check whether the protective devices on the hose crimping machine are complete. If they are not installed, it is forbidden to drive the intermediate frequency tube pressing machine. There should be good grounding and electrical disconnection, and the voltage should be stable. Check the lubricating parts of the hose crimping machine, and add enough oil when there is no oil or no oil. When withholding hoses of different specifications, the indenters of different specifications should be replaced. When oil leakage is found after long-term use, the seals in the oil cylinder and pipe valve system should be replaced in time. The hydraulic oil is 46# Great Wall brand anti-wear hydraulic oil, and the oil temperature is usually controlled at 30℃~35℃.
In the course of use, dust and other debris will inevitably enter, and the mold directly contacts the withheld pipe fittings, so the cleanliness of the connecting mold is also one of the conditions for extending the service life of the crimping machine and the mold. The strong magnetic mold is adsorbed on the mold seat by super-strong magnetic force. The contact surface between the mold and the mold seat should be kept clean. Always wipe the bottom of the mold and the contact surface of the mold seat with clean cotton yarn. After wiping clean, oil the mold immediately to prevent dust particles. The entry of impurities and other impurities will cause the wear of the mold and the mold seat.
Keyword:
hydraulic,hose,crimp,fittings,hydraulic,hose,crimp,tool,hydraulic,hose,crimped,hydraulic,hose,crimper,for,sale,uk,hydraulic,hose,crimper,,hydraulic,hose,crimper,package,hydraulic,hose,crimper,portable,hydraulic,hose,crimper,price,hydraulic,hose,crimper,set
Products
CONTACT
Mona Tel: +8618522290645
Email: mona@bntflex.com
Wechat/Whatsapp:+8618522290645
Skype: barnettcrimpingmachine
Follow Us
Copyright © 2023 Dalian Barnett Flex Hydraulics Co.,Ltd.