NEWS CENTER
How to identify the pros and cons of the hose crimping machine
- Categories:Company News
- Author:
- Origin:
- Time of issue:2021-03-22
- Views:0
(Summary description)How to identify the pros and cons of the hose crimping machine
To identify the pros and cons of the hose crimping machine, we can use the methods of one look, two listen, and three measurements to identify:
1. Look: Observe visually whether the hydraulic fittings and electrical components selected by the pipe locking machine are brand-name products or are produced by regular manufacturers; whether the circuit configuration is regular; whether the design of the oil station pipeline is reasonable; whether there is oil leakage at the connection. If the above passes the visual inspection, you can proceed to the next step.
2. Listen: turn on the device after plugging in the power supply, and listen to whether the device is running normally. If there is abnormal noise, it is often caused by the installation coaxiality of the motor and the oil pump. Another possibility is caused by the unreasonable selection of the oil pump displacement and pipe diameter, and the quality of the selected motor or oil pump. Not very well caused.
3. Measurement: Finally, the main parameters of the equipment are measured
3.1 Keep the equipment in a dry running state, touch each module block with your hand, and there should be no jitter in the hand, otherwise it will be regarded as a substandard product.
3.2 Mount the equipment on the mold, crimp a sample joint, measure the crimp joint with a caliper or a micrometer, the roundness and taper should be buckled within 0.1mm, which is considered excellent.
3.3 Mold base hardness and mold hardness are also the key to the normal use of the equipment in the future. Customers can request manufacturers to use a desktop or portable hardness tester to test the mold base or mold. When the hardness of the mold base is lower than Rockwell HRC60 and the mold hardness is lower than Rockwell HRC50, it will affect the withholding quality of the hose.
3.4 The last is to inspect the eight-petal uniform indexing of the mold base of the equipment and the flushness of the mold. Good equipment will specifically control and adjust these two parameters, while some low-quality equipment does not control the above two parameters.
How to identify the pros and cons of the hose crimping machine
(Summary description)How to identify the pros and cons of the hose crimping machine
To identify the pros and cons of the hose crimping machine, we can use the methods of one look, two listen, and three measurements to identify:
1. Look: Observe visually whether the hydraulic fittings and electrical components selected by the pipe locking machine are brand-name products or are produced by regular manufacturers; whether the circuit configuration is regular; whether the design of the oil station pipeline is reasonable; whether there is oil leakage at the connection. If the above passes the visual inspection, you can proceed to the next step.
2. Listen: turn on the device after plugging in the power supply, and listen to whether the device is running normally. If there is abnormal noise, it is often caused by the installation coaxiality of the motor and the oil pump. Another possibility is caused by the unreasonable selection of the oil pump displacement and pipe diameter, and the quality of the selected motor or oil pump. Not very well caused.
3. Measurement: Finally, the main parameters of the equipment are measured
3.1 Keep the equipment in a dry running state, touch each module block with your hand, and there should be no jitter in the hand, otherwise it will be regarded as a substandard product.
3.2 Mount the equipment on the mold, crimp a sample joint, measure the crimp joint with a caliper or a micrometer, the roundness and taper should be buckled within 0.1mm, which is considered excellent.
3.3 Mold base hardness and mold hardness are also the key to the normal use of the equipment in the future. Customers can request manufacturers to use a desktop or portable hardness tester to test the mold base or mold. When the hardness of the mold base is lower than Rockwell HRC60 and the mold hardness is lower than Rockwell HRC50, it will affect the withholding quality of the hose.
3.4 The last is to inspect the eight-petal uniform indexing of the mold base of the equipment and the flushness of the mold. Good equipment will specifically control and adjust these two parameters, while some low-quality equipment does not control the above two parameters.
- Categories:Company News
- Author:
- Origin:
- Time of issue:2021-03-22
- Views:0
How to identify the pros and cons of the hose crimping machine
To identify the pros and cons of the hose crimping machine, we can use the methods of one look, two listen, and three measurements to identify:
1. Look: Observe visually whether the hydraulic fittings and electrical components selected by the pipe locking machine are brand-name products or are produced by regular manufacturers; whether the circuit configuration is regular; whether the design of the oil station pipeline is reasonable; whether there is oil leakage at the connection. If the above passes the visual inspection, you can proceed to the next step.
2. Listen: turn on the device after plugging in the power supply, and listen to whether the device is running normally. If there is abnormal noise, it is often caused by the installation coaxiality of the motor and the oil pump. Another possibility is caused by the unreasonable selection of the oil pump displacement and pipe diameter, and the quality of the selected motor or oil pump. Not very well caused.
3. Measurement: Finally, the main parameters of the equipment are measured
3.1 Keep the equipment in a dry running state, touch each module block with your hand, and there should be no jitter in the hand, otherwise it will be regarded as a substandard product.
3.2 Mount the equipment on the mold, crimp a sample joint, measure the crimp joint with a caliper or a micrometer, the roundness and taper should be buckled within 0.1mm, which is considered excellent.
3.3 Mold base hardness and mold hardness are also the key to the normal use of the equipment in the future. Customers can request manufacturers to use a desktop or portable hardness tester to test the mold base or mold. When the hardness of the mold base is lower than Rockwell HRC60 and the mold hardness is lower than Rockwell HRC50, it will affect the withholding quality of the hose.
3.4 The last is to inspect the eight-petal uniform indexing of the mold base of the equipment and the flushness of the mold. Good equipment will specifically control and adjust these two parameters, while some low-quality equipment does not control the above two parameters.
Scan the QR code to read on your phone
CONTACT FORM
We’ll take the time to explain the recommended solution and its price
CONTACT
Mona Tel: +8618522290645
Email: mona@bntflex.com
Wechat/Whatsapp:+8618522290645
Skype: barnettcrimpingmachine
Copyright © 2019 Dalian Barnett Flex Hydraulics Co.,Ltd. 辽ICP备20000203号