The installation and debugging of BNT50 hose crimping machine need attention
Time of issue:
2020-11-02
1. The hose crimping machine should be transported by a forklift, and the bottom of the machine should be stressed, and the body is not allowed to tilt. It is strictly forbidden to lift the lock and the ruler. 2. The hose crimping machine must be horizontally fixed on a stable foundation and grounded. 3. Open the casing and add 55-60 liters of No. 46 anti-wear hydraulic oil to the oil tank (the hydraulic oil must be clean, otherwise it will damage the service life of the equipment). Note: If the hydraulic oil is added too little, it will cause the oil temperature to rise too fast and too high, the viscosity of the oil decreases too fast, the oil becomes too thin, and the sealing ring may not seal the oil, resulting in a rise in system pressure Not going up. 4. Connect the power cord to the power supply specified by the machine, and move the motor to observe the direction of rotation. The direction of rotation of the motor should be consistent with the direction indicated by the arrow on the oil pump label. 5. The ruler is located on the front cover of the cylinder and is used to adjust the shrinkage of the crimping sleeve. Adjust clockwise to decrease shrinkage; adjust counterclockwise to increase shrinkage. The ruler seat is pressed against the end surface of the cylinder by the spring force of the three screws. When you pull the ruler by hand (vertical to the end of the cylinder), the ruler seat should be able to leave the cylinder end cover flexibly. After being loosened, it will be automatically compressed on the end of the cylinder by the spring force. Cover. Before starting to withhold, check carefully whether the scale is flexible. Do not fasten the scale to the end cover of the cylinder with screws, otherwise the scale will be damaged. 6. The pressure of the machine system is adjusted by the overflow valve. Adjust the pressure clockwise to increase, and adjust the pressure counterclockwise to decrease (it has been adjusted at the factory, and you can adjust it if necessary, but it must never exceed the rated pressure of the oil pump). 7. The speed of mold opening speed is controlled by the diverter valve and adjusted clockwise to increase the speed of mold opening, and adjust it counterclockwise to slow down the speed of mold opening. However, if the mold opening speed is too fast, the noise will increase (it has been adjusted at the factory You can adjust it if necessary).
1. The hose crimping machine should be transported by a forklift, and the bottom of the machine should be stressed, and the body is not allowed to tilt. It is strictly forbidden to lift the lock and the ruler.
2. The hose crimping machine must be horizontally fixed on a stable foundation and grounded.
3. Open the casing and add 55-60 liters of No. 46 anti-wear hydraulic oil to the oil tank (the hydraulic oil must be clean, otherwise it will damage the service life of the equipment). Note: If the hydraulic oil is added too little, it will cause the oil temperature to rise too fast and too high, the viscosity of the oil decreases too fast, the oil becomes too thin, and the sealing ring may not seal the oil, resulting in a rise in system pressure Not going up.
4. Connect the power cord to the power supply specified by the machine, and move the motor to observe the direction of rotation. The direction of rotation of the motor should be consistent with the direction indicated by the arrow on the oil pump label.
5. The ruler is located on the front cover of the cylinder and is used to adjust the shrinkage of the crimping sleeve. Adjust clockwise to decrease shrinkage; adjust counterclockwise to increase shrinkage. The ruler seat is pressed against the end surface of the cylinder by the spring force of the three screws. When you pull the ruler by hand (vertical to the end of the cylinder), the ruler seat should be able to leave the cylinder end cover flexibly. After being loosened, it will be automatically compressed on the end of the cylinder by the spring force. Cover. Before starting to withhold, check carefully whether the scale is flexible. Do not fasten the scale to the end cover of the cylinder with screws, otherwise the scale will be damaged.
6. The pressure of the machine system is adjusted by the overflow valve. Adjust the pressure clockwise to increase, and adjust the pressure counterclockwise to decrease (it has been adjusted at the factory, and you can adjust it if necessary, but it must never exceed the rated pressure of the oil pump).
7. The speed of mold opening speed is controlled by the diverter valve and adjusted clockwise to increase the speed of mold opening, and adjust it counterclockwise to slow down the speed of mold opening. However, if the mold opening speed is too fast, the noise will increase (it has been adjusted at the factory You can adjust it if necessary).
Keyword:
the,of,to,and,is,it,oil,be,by
Products
CONTACT
Mona Tel: +8618522290645
Email: mona@bntflex.com
Wechat/Whatsapp:+8618522290645
Skype: barnettcrimpingmachine
Follow Us
Copyright © 2023 Dalian Barnett Flex Hydraulics Co.,Ltd.