Talking about the skills in the operation of the crimping machine
Time of issue:
2021-11-15
Talking about the skills in the operation of the crimping machine With the improvement of the machining accuracy of the crimping machine, in order to reduce the positioning error and improve the machining accuracy, the manufacturing accuracy of the fixture is required to be higher. The positioning hole distance accuracy of the high-precision fixture is as high as ±5μm, and the verticality of the fixture supporting surface reaches 0.01mm/300mm, parallel The degree is as high as 0.01mm/500mm. The accuracy of the crimping machine fixture has been improved to the micron level. In order to meet the needs and economy of different industries, the clamp has different models and different grades of accuracy standards for selection. 1. Check the surroundings of the work site and remove all the debris that hinders work and walking. There should be no oil on the ground to avoid slipping. 2. Before the operation, put the enlarged handle on the working position, start the motor for three minutes, and reciprocate for two minutes without load, and grease each mold base. 3. At the end of the operation, the mold base and pressure sleeve should be wiped clean and buttered, and the mold base and pressure sleeve should not be too close (the pressure sleeve and mold base do not touch), and finally stop, loosen the enlarged handle, and put it in Stop in an emergency position to relax the inner tension spring. 4. When crimping the large elbow high-pressure pipe and cannot reach into the machine, the enlarged handle should be moved to the emergency stop position. After putting it in, move the enlarged handle to the working position, then the withholding can be carried out. After the withholding is finished, move it back. Emergency stop position, turn around and put in, and then move the enlarged handle into the working position for crimping. 5. Check whether the protective equipment on the crimping machine is intact. If it is not installed, it is forbidden to drive. The intermediate frequency crimping machine should have excellent grounding and electrical insulation, and the voltage should be stable. 6. Check the smooth parts of the crimping machine, and add enough oil when there is no oil or no oil. 7. When crimping hoses of different standards, the indenter of different standards should be replaced. 8. When oil leakage is found after long-term use, the seals in the cylinder and pipe valve system should be replaced in time.
Talking about the skills in the operation of the crimping machine
With the improvement of the machining accuracy of the crimping machine, in order to reduce the positioning error and improve the machining accuracy, the manufacturing accuracy of the fixture is required to be higher. The positioning hole distance accuracy of the high-precision fixture is as high as ±5μm, and the verticality of the fixture supporting surface reaches 0.01mm/300mm, parallel The degree is as high as 0.01mm/500mm. The accuracy of the crimping machine fixture has been improved to the micron level. In order to meet the needs and economy of different industries, the clamp has different models and different grades of accuracy standards for selection.
1. Check the surroundings of the work site and remove all the debris that hinders work and walking. There should be no oil on the ground to avoid slipping.
2. Before the operation, put the enlarged handle on the working position, start the motor for three minutes, and reciprocate for two minutes without load, and grease each mold base. 3. At the end of the operation, the mold base and pressure sleeve should be wiped clean and buttered, and the mold base and pressure sleeve should not be too close (the pressure sleeve and mold base do not touch), and finally stop, loosen the enlarged handle, and put it in Stop in an emergency position to relax the inner tension spring.
4. When crimping the large elbow high-pressure pipe and cannot reach into the machine, the enlarged handle should be moved to the emergency stop position. After putting it in, move the enlarged handle to the working position, then the withholding can be carried out. After the withholding is finished, move it back. Emergency stop position, turn around and put in, and then move the enlarged handle into the working position for crimping.
5. Check whether the protective equipment on the crimping machine is intact. If it is not installed, it is forbidden to drive. The intermediate frequency crimping machine should have excellent grounding and electrical insulation, and the voltage should be stable.
6. Check the smooth parts of the crimping machine, and add enough oil when there is no oil or no oil.
7. When crimping hoses of different standards, the indenter of different standards should be replaced.
8. When oil leakage is found after long-term use, the seals in the cylinder and pipe valve system should be replaced in time.
Keyword:
the,and,of,in,is,be,to,crimping,should,hose,swager,hose,swaging,hose,swaging,machine,hose,swaging,machines,hoses,and,fittings,hoses,crimper,hoses,hydraulic,hoses,hydraulics,hoses,rubber,hot,crimping,machine,hose,crimper,hose,crimping,machine,hose,machine
Products
CONTACT
Mona Tel: +8618522290645
Email: mona@bntflex.com
Wechat/Whatsapp:+8618522290645
Skype: barnettcrimpingmachine
Follow Us
Copyright © 2023 Dalian Barnett Flex Hydraulics Co.,Ltd.