The specific method of operation of the crimping machine
Time of issue:
2021-11-21
The specific method of operation of the crimping machine The crimping machine is a hydraulic equipment used to crimp the hose assembly. It applies the shrinking force to the matched metal joint through the dies of the crimping machine, and firmly crimps the metal joint on the matched high-pressure oil hose for construction machinery or automobile. Brake pipes, oil hoses, air conditioning hoses, power hoses. 1. Look around the work site and remove all debris that hinders work and walking. There should be no oil stains on the ground to avoid slipping. 2. Before the operation, place the enlarged handle on the working position, start the motor for three minutes, and reciprocate for two minutes without load, and grease each mold base. 3. At the end of the operation, the mold base and pressure sleeve should be wiped clean and buttered, and the mold base and pressure sleeve should not be too close (the pressure sleeve and mold base do not touch), and finally stop, loosen the enlarged handle, and put it in. Stop in an emergency position to relax the inner tension spring. 4. When crimping the large elbow high-pressure pipe and cannot reach into the machine, the enlarged handle should be moved to the emergency stop position. After putting it in, move the enlarged handle to the working position, then the withholding can be carried out. After the withholding is finished, move back to the emergency stop. Position, turn around and put in, and then move the enlarged handle into the working position for crimping. 5. Check whether the protective equipment on the crimping machine is intact. If it is not installed, it is forbidden to drive. The intermediate frequency crimping machine should have excellent grounding and electrical insulation, and the voltage should be stable. 6. Check the smooth parts of the crimping machine, and add enough oil when there is no oil or no oil. 7. When crimping hoses of different standards, the indenter of different standards should be replaced.
The specific method of operation of the crimping machine
The crimping machine is a hydraulic equipment used to crimp the hose assembly. It applies the shrinking force to the matched metal joint through the dies of the crimping machine, and firmly crimps the metal joint on the matched high-pressure oil hose for construction machinery or automobile. Brake pipes, oil hoses, air conditioning hoses, power hoses.
1. Look around the work site and remove all debris that hinders work and walking. There should be no oil stains on the ground to avoid slipping.
2. Before the operation, place the enlarged handle on the working position, start the motor for three minutes, and reciprocate for two minutes without load, and grease each mold base.
3. At the end of the operation, the mold base and pressure sleeve should be wiped clean and buttered, and the mold base and pressure sleeve should not be too close (the pressure sleeve and mold base do not touch), and finally stop, loosen the enlarged handle, and put it in. Stop in an emergency position to relax the inner tension spring.
4. When crimping the large elbow high-pressure pipe and cannot reach into the machine, the enlarged handle should be moved to the emergency stop position. After putting it in, move the enlarged handle to the working position, then the withholding can be carried out. After the withholding is finished, move back to the emergency stop. Position, turn around and put in, and then move the enlarged handle into the working position for crimping.
5. Check whether the protective equipment on the crimping machine is intact. If it is not installed, it is forbidden to drive. The intermediate frequency crimping machine should have excellent grounding and electrical insulation, and the voltage should be stable.
6. Check the smooth parts of the crimping machine, and add enough oil when there is no oil or no oil.
7. When crimping hoses of different standards, the indenter of different standards should be replaced.
Keyword:
the,and,crimping,to,be,machine,should,of,is,hydraulic,electrical,crimping,tool,hydraulic,fitting,hydraulic,fitting,crimper,hydraulic,fitting,crimping,tool,hydraulic,fitting,machine,hydraulic,hose,and,fittings,hydraulic,fittings
Previous
Products
CONTACT
Mona Tel: +8618522290645
Email: mona@bntflex.com
Wechat/Whatsapp:+8618522290645
Skype: barnettcrimpingmachine
Follow Us
Copyright © 2023 Dalian Barnett Flex Hydraulics Co.,Ltd.