Talking About The Role Of Withholding Machine Cylinder
Time of issue:
2021-12-27
Talking about the role of withholding machine cylinder The hydraulic cylinder of the crimping machine and the pipe pressing machine is mainly used in places that need to support heavy objects for a long time. It can still support heavy objects when the oil pressure is removed, and it is safe and reliable. It can be used underwater, single-acting, load retraction, and the nut self-locking makes the load safer. Especially in large-scale projects, it is an easy-to-operate control and self-locking jack. It is designed with a safety pressure holding device and a built-in pressure relief valve to prevent overload. To protect the self-locking jack to facilitate safe operation. The user of the crimping machine will feel that the machine is hot during use. In order to make the crimping machine overload and work for a long time, open the crimping machine to dissipate heat. This is a wrong method. Its Z will eventually cause the crimping machine to fail Speed up the damage. How to make the crimping machine better heat dissipation? 1. The user should understand the rules and regulations and safe operation procedures, master the sequence of turning on and off the crimping machine, and understand and master the structural principle of the crimping machine. 2. The dirt in the solenoid valve should be cleaned up in time during use, and the main power supply should be disconnected when maintaining the crimping machine. ? After the operation is over, unplug the power plug, put away the power cord, and clean up the site before the personnel can leave. 3. If the crimping machine becomes hot, reset the foot switch first, and then restart it after shutting down for 2 minutes. Z It is important to have a reasonable heat dissipation area to keep the oil temperature within a reasonable range. Generally, if the crimping machine is overheated, it is necessary to check whether the heat dissipation area of the electrical circuit of the crimping machine is working normally. Servo motors or variable frequency motors often test the surface temperature or noise, and they must be dealt with in time. When the system load changes, simply control the oil to maintain a stable temperature. It is necessary to install a cooling device. Outside dust, sand, etc., friction will also generate heat during the operation of the crimping machine, and the leaking oil flowing back to the oil tank will enter the hydraulic oil. In addition, when repairing, a little carelessness will also cause magazines etc. to enter the hydraulic oil.
Talking about the role of withholding machine cylinder
The hydraulic cylinder of the crimping machine and the pipe pressing machine is mainly used in places that need to support heavy objects for a long time. It can still support heavy objects when the oil pressure is removed, and it is safe and reliable. It can be used underwater, single-acting, load retraction, and the nut self-locking makes the load safer. Especially in large-scale projects, it is an easy-to-operate control and self-locking jack. It is designed with a safety pressure holding device and a built-in pressure relief valve to prevent overload. To protect the self-locking jack to facilitate safe operation.
The user of the crimping machine will feel that the machine is hot during use. In order to make the crimping machine overload and work for a long time, open the crimping machine to dissipate heat. This is a wrong method. Its Z will eventually cause the crimping machine to fail Speed up the damage. How to make the crimping machine better heat dissipation?
1. The user should understand the rules and regulations and safe operation procedures, master the sequence of turning on and off the crimping machine, and understand and master the structural principle of the crimping machine.
2. The dirt in the solenoid valve should be cleaned up in time during use, and the main power supply should be disconnected when maintaining the crimping machine. ? After the operation is over, unplug the power plug, put away the power cord, and clean up the site before the personnel can leave.
3. If the crimping machine becomes hot, reset the foot switch first, and then restart it after shutting down for 2 minutes.
Z It is important to have a reasonable heat dissipation area to keep the oil temperature within a reasonable range.
Generally, if the crimping machine is overheated, it is necessary to check whether the heat dissipation area of the electrical circuit of the crimping machine is working normally. Servo motors or variable frequency motors often test the surface temperature or noise, and they must be dealt with in time. When the system load changes, simply control the oil to maintain a stable temperature. It is necessary to install a cooling device.
Outside dust, sand, etc., friction will also generate heat during the operation of the crimping machine, and the leaking oil flowing back to the oil tank will enter the hydraulic oil. In addition, when repairing, a little carelessness will also cause magazines etc. to enter the hydraulic oil.
Keyword:
hydraulic,hose,press,hydraulic,house,hose,hydraulic,hose,fittings,hydraulic,swaging,machine,hydraulic,hose,crimping,tool,hydraulic,hose,machine,hydraulic,crimping,machine,hydraulic,hose,crimping,machine,for,sale,hydraulic,pipe,crimper,,hose,crimping,tool
Products
CONTACT
Mona Tel: +8618522290645
Email: mona@bntflex.com
Wechat/Whatsapp:+8618522290645
Skype: barnettcrimpingmachine
Follow Us
Copyright © 2023 Dalian Barnett Flex Hydraulics Co.,Ltd.