News Center

We continue to develop and improve ourselves, and collaborate with our customers to develop and create the future.

Design and structure principle of hydraulic hose crimping machine

Design and structure principle of hydraulic hose crimping machine The structure of the crimping machine. The main machine and hydraulic system of the hose crimping machine are designed as a centralized assembly box structure, and a hose joint socket that can be connected with the pipeline of the hydraulic station is reserved on the box body. Spare molds, common tools and other spare parts can be stored in the box. The main machine of the hose crimping machine is the hydraulic cylinder 1, the taper sleeve 8 and the piston rod 5 are connected with the back cap 6 as a whole, and the punch block 9 and the center sleeve 10 are connected with the rear positioning plate 11 by the nut. The high pressure of the hydraulic system is The liquid enters the piston cavity from the port, pushes the piston rod outwards, and presses the outer cone surface of the punch block through the inner cone surface of the cone sleeve 8, so that the mold is elastically contracted radially, and the metal joint is compressed to produce a certain amount of radial plasticity. Deformation to achieve the purpose of connecting the metal joint and the hydraulic hose. When the oil is supplied from the reverse oil port, the piston rod retracts, the taper sleeve releases the compression of the counter block, and the block recovers due to the elasticity of the spring, completing a crimping cycle of the joint. The working principle of the liquid compression tube machine When working, first fit the end of the hydraulic hose with the metal pipe joint 4, and insert it into the predetermined position of the inner hole of the punching block. Then turn the operating valve 7 to the left position. At this time, the host A cavity is a high pressure cavity, and the B cavity is a low pressure cavity. The piston moves to the right under the action of the liquid pressure, and the piston rod drives the cone sleeve to move axially to the right to compress the punch block. In this way, the punch block is forced to contract radially, and the metal pipe joint is crimped until the preset compression amount is reached. This process is called the compression process. Then turn the operating valve to the middle position and pause for a certain period of time (about 1 min). At this time, the A and B chambers are respectively closed and in a pressure-holding state, and the liquid discharged by the liquid pump returns to the liquid tank through the operating valve. This process is called the holding pressure process. Next, turn the operating valve to the right. At this time, the A cavity becomes a low pressure cavity, and the B cavity becomes a high pressure cavity. The piston moves to the left under the action of the liquid pressure, and the piston rod drives the cone sleeve to retract in the opposite direction. After the pressure is released, the punch block is opened under the action of the spring until the taper sleeve returns to the original position. At this time, pull out the crimped hydraulic hose from the mold. This process is called the rollback process. After the three processes of compression, pressure holding and retreat, one cycle of joint crimping is completed. When the host is in the state of designing technical parameters, each crimping cycle is completed for about 3 minutes at most. The design of the main body of the crimping machine 1 The structure design of the center sleeve and the cover 1.1 The structure design of the center sleeve The center sleeve is a round sleeve with a shaft shoulder on the shaft shoulder and a threaded hole on the shaft shoulder. On the board. Since the center sleeve and the taper sleeve are universal, it must also meet the requirements of compressed pipe diameters of 6 mm, 8 mm, 10 mm, 16 mm, 19 mm, 25 mm, 32 mm, so the largest diameter is now The center sleeve of the 32 mm tube is the reference design center sleeve, and then the size of the punch block for different pipe diameters is designed.

11-19

2021

Why the crimping machine is selling well

Why the crimping machine is selling well More than 95% of current crimping machines use hydraulic systems, which are occasionally used in pressure-only low-pressure tubing crimping machines or sanitary pipe crimping machines that are powered by pneumatic systems or levers. The oil pump of the hydraulic system is equivalent to the human heart, and its role is very important. The gear pump is used as the power source of the crimping machine. It is often considered that its cost is lower, the cost is saved, and the cleanliness of the oil is not high-level elements, but its defects For: The supply pressure is low, only equivalent to 60% of the plunger pump pressure, the noise is large, and the service life is short. Due to the low supply pressure, manufacturers often consider sacrificing the expansion and contraction capacity of the crimping machine in order to increase the crimping pressure. Improve the conversion of axial force and radial force of the crimping machine, so it is often possible to choose a gear pump crimping machine when the customer's requirements are not high. Because the reputation and reputation are good, the customer's evaluation to a certain extent represents the degree of product quality assurance, and the machine is good or not, the customer's evaluation is a very intuitive reflection. 1. The principle of dual hydraulic circuit operation is adopted, that is, the advance and retreat of the piston and the opening and contraction of the mold are all driven by the hydraulic power source. It not only moves smoothly and returns quickly, but also does not cause the mold to be locked due to the spring return. Moreover, the design of the cylinder locking system is through front and back, which is easy to withhold various special-shaped elbows. 2. The hydraulic system is composed of a motor, an oil pump, a solenoid valve, a pressure regulating valve and a hydraulic valve. The purpose of quick return, and the speed is adjustable, noise and system pressure are reduced. 3. In terms of electrical control system, the control circuit is suitable for PLC circuit, which is easy to check and repair the circuit, easy to maintain, and simple to replace. 4. The crimping mold and mold base adopt a non-accumulative error-free processing technology to ensure that the crimping lines of the product after crimping are evenly spaced, and there is no big or small head phenomenon. Using plunger pump as the power source of the crimping machine, the advantages are: high pressure (300kg/cm2), long pump life, low noise, such as YCY series can automatically variable fuel supply, low pressure large flow, high pressure small flow, the same specifications The motor saves 30% of electricity and the hose that is crimped is not easy to leak oil. Because the system is high, it can be designed to achieve a larger opening under the same crimping pressure, so that customers can use it for a long time. But its disadvantages are: high cost, the same displacement pump, the plunger pump is 8-10 times that of the gear pump, which increases the cost of a single machine, and requires relatively high oil cleanliness, but considering the basic performance Input-output ratio, choosing YCY system variable pump crimping machine will be very cost-effective.

11-17

2021

Let customers understand the application advantages of hydraulic crimping machine

Let customers understand the application advantages of hydraulic crimping machine When the hose crimping machine crimps the high-pressure oil pipe, if the crimping amount is too small, then the pressure between the joint and the hose is too loose, under the action of the oil pressure, the crimping machine hose may come out of the joint at the early stage of use, if the crimping amount is too large , Then the joint and the hose are pressed too tightly, which will easily cause the inner layer of the hose to be partially destroyed and cracks. The hydraulic oil will directly enter the steel wire layer from the crack, and then leak out along the gap between the steel wires to the end of the outer jacket, or continuously along The steel wire layer flees somewhere and accumulates, causing the outer layer of glue to bulge and even break. From raw rubber plasticizing to break the macromolecular chain to make the molecular weight drop to achieve plasticity, and fully mix and average it with various compounding agents, to make high-elasticity and high-quality rubber pipes under the process conditions of heating and pressure. Throughout the process, we are striving to seek new technologies and techniques for hose processing to improve efficiency, improve quality, and reduce labor intensity. The new technology of hose processing requires a high degree of continuity, high speed and automation of the molding process, and the final qualified pipe can be produced in one molding. Advantages of hydraulic crimping machine: 1. It can be customized according to the needs of customers. 2. It can be used for forming different shapes of pipe fittings, automobile oil pipes, air pipes, water pipes, air-conditioning pipe connections and other parts. 3. It adopts hydraulic power, stable work, high rejection rate, low vibration, low noise, and the machine structure is solid, compact and easy to operate. In order to withhold the machine on the locking mechanism components, not only high-quality alloy steel materials are selected, but also a unique heat treatment process is adopted. Therefore, the longer service life of the crimping machine is inseparable from the rationality of material selection, heat treatment, mechanical processing technology and structure! Regarding the double-column crimping machine and C-type crimping machine, because it is not convenient to set the dead position, it is necessary to use the numerical control method to control the crimping size.

11-16

2021

Talking about the skills in the operation of the crimping machine

Talking about the skills in the operation of the crimping machine With the improvement of the machining accuracy of the crimping machine, in order to reduce the positioning error and improve the machining accuracy, the manufacturing accuracy of the fixture is required to be higher. The positioning hole distance accuracy of the high-precision fixture is as high as ±5μm, and the verticality of the fixture supporting surface reaches 0.01mm/300mm, parallel The degree is as high as 0.01mm/500mm. The accuracy of the crimping machine fixture has been improved to the micron level. In order to meet the needs and economy of different industries, the clamp has different models and different grades of accuracy standards for selection. 1. Check the surroundings of the work site and remove all the debris that hinders work and walking. There should be no oil on the ground to avoid slipping. 2. Before the operation, put the enlarged handle on the working position, start the motor for three minutes, and reciprocate for two minutes without load, and grease each mold base. 3. At the end of the operation, the mold base and pressure sleeve should be wiped clean and buttered, and the mold base and pressure sleeve should not be too close (the pressure sleeve and mold base do not touch), and finally stop, loosen the enlarged handle, and put it in Stop in an emergency position to relax the inner tension spring. 4. When crimping the large elbow high-pressure pipe and cannot reach into the machine, the enlarged handle should be moved to the emergency stop position. After putting it in, move the enlarged handle to the working position, then the withholding can be carried out. After the withholding is finished, move it back. Emergency stop position, turn around and put in, and then move the enlarged handle into the working position for crimping. 5. Check whether the protective equipment on the crimping machine is intact. If it is not installed, it is forbidden to drive. The intermediate frequency crimping machine should have excellent grounding and electrical insulation, and the voltage should be stable. 6. Check the smooth parts of the crimping machine, and add enough oil when there is no oil or no oil. 7. When crimping hoses of different standards, the indenter of different standards should be replaced. 8. When oil leakage is found after long-term use, the seals in the cylinder and pipe valve system should be replaced in time.

11-15

2021

Talking about the principle of purchase and use of hose crimping machine

Talking about the principle of purchase and use of hose crimping machine The classification of hose crimping machine can be divided into hydraulic high pressure hose crimping machine, brake hose crimping machine, air-conditioning hose crimping machine, power hose crimping machine, etc. according to the function of use, and can be divided into straight-cylinder hose crimping machine according to the mechanical structure. Machine, double-column hose crimping machine, open-type hose crimping machine, C-type hose crimping machine, for example, according to the control method can be divided into electromechanical hose crimping machine The tube machine is widely used, and its advantages and technical performance are as follows: 1. The principle of dual hydraulic circuit operation is adopted, that is, the advance and retreat of the piston and the opening and contraction of the mold are all driven by the hydraulic power source. It not only moves steadily and returns quickly, but also does not cause the phenomenon of a spring to return, which makes the mold not open and locks up. Moreover, the design of the cylinder locking system is through front and back, which is easy to withhold various special-shaped elbows.  2. The hydraulic system consists of a motor, an oil pump, a solenoid valve, a pressure regulating valve and a hydraulic valve to form a dual hydraulic circuit with forward and retreat movement, and a quick drain valve circuit is added to the dual hydraulic circuit to achieve better The purpose of quick return, and the speed is adjustable, noise and system pressure are reduced.   3. In terms of electrical control system, the control circuit is suitable for PLC circuit, which is easy to check and repair the circuit, easy to maintain, and simple to replace.   4. The crimping mold and mold base adopt a non-accumulative error-free processing technology to ensure that the crimping lines of the product after crimping are evenly spaced, and there is no big or small head phenomenon.   5. For the permanent mechanical precision and life of the pipe press, not only high-quality alloy steel materials are selected for the components of the locking mechanism, but also a unique heat treatment process is adopted. Therefore, the longer service life of the pipe press is inseparable from the rationality of material selection, heat treatment, machining technology and structure!

11-14

2021

What are the precautions for maintenance of the crimping machine?

What are the precautions for maintenance of the crimping machine? The crimping machine is a kind of hydraulic equipment used to crimp the pipe assembly. It applies the shrinking force to the matched metal joint through the mold of the crimping machine, and firmly crimps the metal joint on the matched high-pressure oil pipe for construction machinery or automobile. Brake pipes, oil pipes, air conditioning pipes, power pipes. The crimping machine is suitable for the crimping of various mechanical high and low pressure oil pipes, air pipes, water pipes, cable joints, automobile air conditioning pipes, automobile power steering pipes, oil pipes, gasoline supply pipes, as well as construction accessories and daily hot water pipes. It is widely used Vehicles, construction machinery, hydraulic machinery, welding and cutting equipment and other industries. Pull out the positioner during transportation to avoid accidental damage. In order to extend the life of your machine and prevent accidents, you must add original hydraulic oil. Before each use, pay attention to brush the lubricating oil (engine oil or hydraulic oil) on the inner cone surface of the front end of the machine head with a small oil brush. Do not buckle rusty joints and pipes to prevent impurities from falling into the machine head. Precautions for maintenance of crimping machine: 1. Frequently inject anti-wear lubricant into the moving surface of the mold base. 2. During the working hours of the non-pressing machine, please cover the dust cover to prevent sundries from falling into the mold base. 3. The hydraulic oil in the oil tank should be replaced when the time limit specified by the hydraulic oil manufacturer is exceeded, or the oil level gauge should be checked visually. If the hydraulic oil is oxidized and darkened, it must be replaced. The maintenance of the crimping machine is three simple steps. The most important thing is the attention of the staff, so that the maintenance of the crimping machine can be better.

11-13

2021

Analyze what is the working principle of the hose crimping machine

Analyze what is the working principle of the hose crimping machine The pressure is accelerated in the nozzle by the main oil pump, thereby forming a negative pressure in the mixing chamber of the nozzle. Due to the entrainment of the negative pressure and the free jet, the oil in the mixing chamber in the oil tank is continuously brought into the diffuser tube. The mixed oil flow is decelerated and boosted in the diffuser tube and then sent to the main oil pump or lubricated oil for the bearing. The oil injector is one of the main equipment of the centrifugal oil pump oil supply system. It is mainly composed of a nozzle, a mixing chamber and a diffuser tube. The hose crimping machine drives the steel pipe to rotate through mechanical transmission and heats it with flame at one end of the steel pipe. When a certain temperature is reached, the heated steel pipe head is driven by a forming die until it reaches the required shape. hose crimping machine structure: Weld a site with channel steel, and the power end is equipped with a motor, a reducer, and a chuck (for pipe clamping, it can be replaced by a lathe chuck). A support base (openable) is installed at the other end, and a heating ring is fixed on the outer end of the support base (8-10 nozzles, welded to a copper pipe ring by gas welding by grabbing the nozzle). On the outermost side is a movable bracket on which an alloy mold is installed. How to use: Fix the tube on the tube press and turn on the heater (ring). After the temperature is reached, the alloy mold is pushed, and the shape of the tube head meets the requirements. The whole process takes about 15 minutes. With the slowdown and delay of infrastructure projects such as real estate and road and bridge construction, the crimping machine industry is affected by the decline in overall economic growth. In the future, under the premise of maintaining overseas markets, it will increase independent product innovation and continue to improve the research and development of crimping machines and pipe crimping machines. Invest in efforts to create value for products and services and maintain a leading position in the industry.

11-12

2021

Analyze what is the working principle of the hose crimping machine

Analyze what is the working principle of the hose crimping machine The pressure is accelerated in the nozzle by the main oil pump, thereby forming a negative pressure in the mixing chamber of the nozzle. Due to the entrainment of the negative pressure and the free jet, the oil in the mixing chamber in the oil tank is continuously brought into the diffuser tube. The mixed oil flow is decelerated and boosted in the diffuser tube and then sent to the main oil pump or lubricated oil for the bearing. The oil injector is one of the main equipment of the centrifugal oil pump oil supply system. It is mainly composed of a nozzle, a mixing chamber and a diffuser tube. The hose crimping machine drives the steel pipe to rotate through mechanical transmission and heats it with flame at one end of the steel pipe. When a certain temperature is reached, the heated steel pipe head is driven by a forming die until it reaches the required shape. hose crimping machine structure: Weld a site with channel steel, and the power end is equipped with a motor, a reducer, and a chuck (for pipe clamping, it can be replaced by a lathe chuck). A support base (openable) is installed at the other end, and a heating ring is fixed on the outer end of the support base (8-10 nozzles, welded to a copper pipe ring by gas welding by grabbing the nozzle). On the outermost side is a movable bracket on which an alloy mold is installed. How to use: Fix the tube on the tube press and turn on the heater (ring). After the temperature is reached, the alloy mold is pushed, and the shape of the tube head meets the requirements. The whole process takes about 15 minutes. With the slowdown and delay of infrastructure projects such as real estate and road and bridge construction, the crimping machine industry is affected by the decline in overall economic growth. In the future, under the premise of maintaining overseas markets, it will increase independent product innovation and continue to improve the research and development of crimping machines and pipe crimping machines. Invest in efforts to create value for products and services and maintain a leading position in the industry.

11-12

2021

< 1...101112...29 > proceed page